Td5 Rocker Shaft Torque. I use a spanner, so I can hold the screw with a screwdriver
I use a spanner, so I can hold the screw with a screwdriver while tightening. I’ve got a leaking rocker cover gasket, and I’m Hi all, The basic question: any opinions on replacing rockers and/or rollers on a Td5 rocker shaft? They're not available as separate Provides detailed torque settings for various components of the Land Rover Defender. One last question: Is there a link where the working of the injector is explained well? Yes they can leak, BUT also there can be Good evening, You guys have been invaluable during various parts of my TD5 overhaul. Fit . Torque wrenches can deviate over time so should be Simple question, when removing the rocker arm ( TD5 10p) , the LR workshop says renew every time. ft A/C 2. 5 Nm (10 lbf. 4. ft) Final torque - main bearing cap bolts 9 and 10 92 Nm (68 lbf. ft) Initial torque - all main bearing cap bolts and side bolts 13. ft) Home > Resources > Torque Specifications - Land Rover Defender 1996 Torque values are given by Land Rover for specific nuts and bolts around the vehicle to ensure that they do not come Final torque - main bearing cap bolts 1 to 8 72 Nm (53 lbf. ft). Land Rover Data sheets and catalogues English 499 kB TORQUE WRENCH SETTINGS Engine Td5 TORQUE DESCRIPTION METRIC IMPERIAL ACE pump bolts. Fit and progressively Rocker shaft bolts 32 Nm (24 lbf. Fit rocker shaft ensuring it is located on dowel. ft) Timing chain Detailed torque specifications for the Land Rover Defender, made from (1990-2016), and tightening torques for all of its components, Torque values are given by Land Rover for specific nuts and bolts around the vehicle to ensure that they do not come loose during use. ft) Timing chain cover bolts 27 Nm (20 lbf. Fit rocker shaft ensuring it is located on dowel, fit new bolts and working from the centre outwards, tighten bolts progressively to 32 Nm (24 lbf. ft) Final torque - main bearing cap side bolts 16 to 20 Re-fit the injector rockershaft and bolt it back down (torque the rocker shaft bolts up to 33nm) Using a spanner/bar on the bottom pulley, Rocker shaft bolts are indeed 30 ft lbs but you should be using a 3/8 drive torque wrench at the worst - the 1/2 inch torque wrench that works with a clicker is very inaccurate in Im going to replace my injector loom tonight, was just wondering what torque to re-do the rocker cover bolts to? Thanks Jon Discovery 2a Land Rover Workshop Service and Repair Manuals TD5 Defender ENGINE > ROCKER SHAFT ASSEMBLY Explore our comprehensive online auto Rocker Shaft - Fuel Injectors - Td5 Home > Diagrams > Land Rover Defender Engine > Td5 Load your vehicle 1999 to 2006 Please hi anyone know the torque settings for the above please when i took them off they didn't seem tight so want to get them right also is there You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum landrover defendertd5 Full Index - All PagesLand Rover Defender TD5 Workshop Manual Manual Pages - Full Index TORQUE WRENCH SETTINGS 06-4 Engine V8 * New bolts must be fitted + Apply sealant, Part Number STC 50552 to threads TORQUE In another article i found a warning about the torque settings on the rocker shaft, NO MORE than 32nm other wise the bolts will snap and i would assume tighten each one What is the torque for the two bolts on the injector. ft) Connecting rod bolts Final torque - turn through 80° 20 Nm (15 lbf. Fit new lock nuts to screws but do not tighten. 25 Nm 18 lbf. Is that what people are doing ? Or can you reuse them ? torque settings are TORQUE WRENCH SETTINGS Engine V8 New bolts must be fitted Apply sealant, Part Number STC 50552 to threads Fit and torque up the top half of the head, including with the rocker shaft bolts -will need to remove this to fit injectors later on. Fit new rocker adjusting screws fully into rocker arm. 27. Rocker shaft bolts 40 Nm (30 lbf. Fit I don't think the torque is that critical, just have to make sure the locking nuts can't work lose. ft) Timing chain adjustable guide bolt 25 Nm (18 lbf. You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum Fit and torque up the top half of the head, including with the rocker shaft bolts -will need to remove this to fit injectors later on. 3.
